Structure · Carbon fiber
Structural reinforcement with carbon fiber in Mallorca
At Armalutx Construction, we provide structural reinforcement with carbon fiber in Mallorca, based in Inca. We bond carbon fiber sheets and fabrics to concrete beams, joists, and columns to increase their load-bearing capacity without increasing their cross-section. We use it when the structural assessment indicates it's necessary, and always on previously repaired concrete.
Why Armalutx for carbon fiber reinforcement
Chosen by diagnosis, not by catalog
We also install Mecanoviga, a steel profile under the joist filled with mortar, and we do steel jacketing and reinforcement. If fiber isn't the solution for your beam, we'll tell you and apply the right one.
First, a healthy support
Before attaching a single sheet, we repair the concrete, treat the reinforcement bars, and fill the section with mortar. This is the work of the construction company, not the installer, and it's what determines how much the reinforcement can withstand.
A structures manager
The work is being carried out by our specialist in charge of structure, together with the technician who signs the calculation and directs the work.
The finished stay, not just reinforced
Shoring, fire protection if required by calculations, false ceiling and finishes, all from the same construction company: we deliver the space ready to use.
What is carbon fiber reinforcement and how does it work?
Carbon fiber is a composite material (CFRP) with extremely high tensile strength and very low weight. It is used in two formats. Rigid sheets are bonded to the underside of beams and joists to increase their resistance to bending. Flexible fabrics wrap columns to confine them or are placed along the sides of beams to resist shear stress. This is one of the techniques we offer in our service. structural reinforcement.
The reinforcement works by bonding: the adhesive transmits the stress from the concrete to the fiber, so everything depends on the substrate. If the concrete is crumbling or the reinforcing bars are rusted, they must be repaired first; without that base, the fiber will detach before it can function. And since it only bears the loads that arrive after it's installed, when the beam is already heavily loaded, it's advisable to unload it or shore it up beforehand.
- Without adding sections
- Without adding weight
- It does not rust
- Quick and clean work
Where it is used: beams, slabs, pillars and walls
These are the most common applications in homes, buildings and premises on the island.
Concrete beams and joists
Sheets on the underside to increase flexural strength without losing headroom.
Slabs with new loads
Bands under the joists or on the slab when the use changes: a premises that are converted into housing, an archive area or heavy machinery.
Pillars
Fabrics that wrap around the pillar and confine it so that it can withstand greater compression. The edges are rounded beforehand so that the fabric is not cut at the corners.
Load-bearing walls
Bands on masonry walls to improve their performance without thickening them or losing usable space.
Old or protected buildings
When the original structure cannot be remade, the fiber reinforces it without changing its geometry and remains hidden under the finish.
When to use carbon fiber and when not to
Carbon fiber works great in its intended place. Outside of it, it's money wasted.
| Situation | Carbon fiber? | To do |
|---|---|---|
| Sound concrete beam that needs more capacity (change of use, calculation error) | Yes, it's a typical case. | Sheets on the underside, with their calculation |
| Pillar that must withstand more compression | Yeah | Wrap it in fabric; if that's not enough, encase it in concrete or steel. |
| Rusty rebar and detached concrete | Yes, after repairing | Clean, treat the reinforcements and replace with mortar before applying the fiber. |
| Beams with advanced aluminosis and non-strength concrete | No: the fiber has nothing to hold onto | Mecanoviga or steel profiles that bear the load |
| Rotten or woodworm-ridden wooden beams | Seldom | Replacement, prosthesis of the beam head or Mecanoviga |
| Element that must withstand a fire | Only protected against fire | Protect the reinforcement or choose another technique |
The technique is determined by the technician who calculates the reinforcement, after the diagnosis.
How to make a carbon fiber reinforcement
From diagnosis to completion, in that order. Your job is to give us access to the room, approve the budget, and choose how you want the final finish.
Inspection and sampling
We inspect the actual condition of the concrete and the reinforcement. If necessary, samples are taken to test their strength.
Reinforcement calculation
A competent technician calculates how much fiber is needed and where, and decides whether the reinforcement needs fire protection.
Preparation of the support
Repair of damaged concrete, treatment of reinforcements, repair mortar, sanded and cleaned surface and rounded edges.
Application
Primer, epoxy adhesive and sheet or fabric, respecting the curing times and temperature requested by the manufacturer.
Control and finishing
The checks requested by the site management, the protection of the reinforcement and the final finish: paint, mortar or false ceiling.
License: the fiber is lightweight, but it's structurally sound.
The fact that the fiber is lightweight and doesn't produce dust doesn't change what it is: an intervention on the load-bearing structure. In the Balearic Islands, such works cannot be processed with prior notification: they require a building permit, along with a project plan from the technician who also oversees the work.
In Palma, there's a nuance. If only intermediate slabs are being partially reinforced, without affecting columns or beams, a prior notification signed by a qualified professional may suffice. The professional will advise you on the appropriate procedure for your specific case before providing a quote.
Frequently asked questions about carbon fiber
Can carbon fiber be applied to any building?
Yes, in any structure where the concrete retains a minimum strength: single-family homes, older buildings, commercial premises, and warehouses. The determining factor is a preliminary study of the substrate, including exploratory excavations and, if necessary, testing. If the concrete is severely degraded, there are better techniques, and we can recommend them to you.
How long does a carbon fiber reinforcement take?
Many projects are completed in just a few days. The pace is determined by the repair of the substrate, if necessary, and the curing of the adhesive, which cannot be accelerated without compromising adhesion. We will provide you with a timeframe for your project after the initial assessment.
Is it necessary to vacate the building during the works?
Normally not. There's no major demolition involved, and work is done in sections, so the rest of the house or premises can often still be used. Only the room where we're working is closed off, and it's a good idea to ventilate it while the resin cures.
Is it more expensive than other reinforcement systems?
The materials are more expensive, but the work is quick, generates minimal debris, and avoids the need to rebuild existing slabs. Compared to a concrete encasement or replacing the slab, it's often more cost-effective; if not, we'll let you know.
How long does a carbon fiber reinforcement last?
Decades, if properly applied and protected from direct sunlight, constant humidity, and fire. Carbon doesn't oxidize, which is very important in a house near the sea, where salt air attacks steel reinforcement.
Is the reinforcement noticeable once it's finished?
No. The sheets are just over a millimeter thick and don't reduce the room's ceiling height. They are covered with paint, mortar, or a false ceiling, and if the reinforcement needs fire protection, that same layer conceals it.
Is carbon fiber effective for aluminosis?
Only if the concrete of the joists retains its strength. With advanced aluminosis, the fiber does not have reliable support, and a complementary beam that assumes the load is recommended, such as the Mecanoviga. If you have doubts about your roofs, start by finding out What is aluminosis and how to detect it.
You might also be interested in
- Structural reinforcement in MallorcaAll techniques: Mecanoviga, special concretes, steel and underpinning.
- Mechanism Beam GuideThe alternative when the joist no longer has strength.
- Elevator installationOpen up the floor slabs for the elevator shaft and reinforce its edges.
- Cracks in walls: when are they dangerousThe signs that call for a diagnosis of the structure.
Budget
Does your structure need more capacity?
Tell us what element concerns you or what change of use you want to make. We'll assess it, diagnose the problem, and prepare a detailed, itemized, written estimate before we begin. If you'd like to discuss it beforehand, call us at 625 16 47 18.
- 625 16 47 18
- info@armalutx.com
- Monday to Friday, from 8:30 a.m. to 4:00 p.m.
- Carrer del General Weyler, 29 · 07300 Inca, Mallorca